FLYSEA Scorch Burning Gel 4oz (120ml) — Precision Wood-Burning Effects Without a Soldering Iron

FLYSEA Scorch Burning Gel 4oz (120ml) — Precision Wood-Burning Effects Without a Soldering Iron

Perfect for NZ crafters, DIYers, and makers who want crisp branded logos, stencils, and lettering on wood, card, leather, and more—minus the hassle of a traditional pyrography pen.

Quick Overview

Meet your new shortcut to pro-level scorched designs. FLYSEA Scorch Burning Gel turns ordinary surfaces into burn-ready canvases: brush or dab through a stencil, let it set, then apply heat to reveal clean, dark, “burned-in” artwork. Ideal for signs, gifts, wedding décor, boards, and boutique product branding. One small bottle goes a long way and plays nicely with reusable stencils, vinyl masks, and laser-cut templates—perfect for batch work and consistent results.

Key Specs (Simplified)

• Format: 1 bottle, 4oz (120ml)
  
• Type: Water-based scorch-activation gel (craft use)
  
• Finish/Effect: Heat-activated, “burned-in” look (depth & tone vary by material and heat)
  
• Tools Needed: Heat gun or similar hot-air tool (not included)
  
• Surfaces (typical): Raw/unfinished wood, light-coloured card, some leathers & papers; always test first
  
• Clean-Up: While wet—soap & water on tools and stencils
  
• Use Style: Brush, sponge, dauber, or stencil application
  
• Made For: Stencilling, branding marks, signage, lettering, pattern fills
  
• Quantity Guidance: A little goes far—thin coats deliver sharper edges
  
• Country Fit: NZ spelling, usage notes, and safety guidance included
  

Note on composition, effect, capacity, usage: Full instructions and care guidance are below (this page) under “How It Works,” “Surface Prep & Application,” and “Safety & Storage.”

Why Kiwi Makers Love It

• No soldering iron needed: Skip the steep pyrography learning curve.
  
• Stencil-friendly: Achieve logo-grade, repeatable detail for small businesses and side hustles.
  
• Batch consistency: Perfect for markets, Etsy/NZ Made stores, and craft fairs.
  
• Time-saving: Faster than traditional wood-burning for lettering and pattern fills.
  
• Clean, sharp edges: Minimal bleed when you prep surfaces properly and use light coats.
  
• Compact & economical: 4oz (120ml) is surprisingly productive for small-to-medium projects.
  

What’s In The Box

• 1 × FLYSEA Scorch Burning Gel, 4oz (120ml) bottle
  
• Basic use & safety notes (on label or insert)
  

Ideal Projects & Use Cases in NZ

• Personalised gifts: Cheese boards, signs, frames, keepsake boxes.
  
• Branding for micro-businesses: Batch-mark product tags, packaging inserts, and timber blanks.
  
• Wedding & event décor: Table numbers, place cards, welcome boards.
  
• Classroom/Makerspace demos: Safer, more controllable than open-flame techniques (adult supervision required).
  
• Prototype & sample runs: Quickly test placements and scales before committing to mass production.
  

How It Works (Simple Steps)

1. Prep the surface: Sand raw wood to fine grit (180–240). Wipe dust away. Avoid sealed or oily woods.
   
2. Position your stencil or mask: Use light tack spray or painter’s tape for crisp alignment.
   
3. Apply a thin coat: Dab or brush very lightly—thin is sharp; thick increases bleed.
   
4. Lift stencil carefully: Let the gel sit for a short dwell (per your tests—often a few minutes).
   
5. Heat-activate: Use a heat gun to apply steady, even heat until the design darkens. Keep moving to avoid hotspots.
   
6. Fine-tune the tone: Longer heat = deeper char. Stop when you like the contrast.
   
7. Optional seal: Once cool and dusted off, add a clear, non-yellowing topcoat if desired (polycrylic or similar).
   

Pro tip: Always run small test swatches on the same material you plan to finish. Different woods (pine vs. birch vs. rimu) take heat differently.

Materials Guide (What Works Best)

• Raw/unfinished wood: The top choice. Tight-grain woods deliver the crispest edges.
  
• Light-coloured card & paper: Quick signage and mock-ups; use lower heat and brief passes.
  
• Some leathers: Vegetable-tanned leather may take a subtle scorch; always patch-test.
  
• Plywood & MDF: Can work but sealers/resins and glue lines affect results—test first.
  

Avoid or be cautious with:

• Varnished/sealed surfaces: The gel may not penetrate; strip or sand back if needed.
  
• Oily/exotic woods: Natural oils can resist the effect or cause uneven tones.
  
• Food-contact zones (unsealed): If decorating boards or utensils, keep designs away from direct food contact and finish with a food-safe topcoat on non-decorated areas.
  

Edge Control & Detail Tips

• Stencil quality matters: Laser-cut mylar or good vinyl masks reduce feathering.
  
• Less is more: Thin application gives crispness; blot off excess from your brush/sponge.
  
• Burn in passes: Build darker tones gradually with multiple heat sweeps rather than one long blast.
  
• Heat distance: Start further away with your heat gun; close in slowly until colour appears.
  
• Mask off overspray zones: Especially for large patterns.
  
• Work cool to warm: If you pre-warm the surface too much, gel may over-react and blur edges.
  

Finishing & Aftercare

• Dust away char: A soft, dry brush or microfibre cloth removes loose residue.
  
• Seal for durability: Clear, non-yellowing acrylic/polycrylic keeps contrast rich and resists smudging.
  
• Avoid harsh cleaners: Wipe gently with a damp cloth once sealed.
  
• Display & store: Keep crafted pieces out of persistent damp and direct harsh UV for best longevity.
  

Safety, Handling & Storage (Read First)

• Ventilation: Use in a well-ventilated space.
  
• PPE: Wear gloves; avoid skin and eye contact.
  
• Heat tools: Treat heat guns with respect—keep away from kids, pets, flammables.
  
• Test first: Patch-test materials and stencils; some substrates react differently.
  
• Food contact caution: Decorative use only; avoid unsealed contact surfaces.
  
• Storage: Keep capped, cool, and upright. Do not freeze.
  
• Disposal: Follow local NZ council guidelines for craft chemicals; don’t pour into drains.
  
• First aid: If contact occurs, rinse with water. If irritation persists, seek medical advice.
  

Frequently Asked Questions

Does it replace a wood-burning pen entirely?
For lettering, logos, and patterns via stencils—often yes. For deep carved lines or textured shading, traditional pyrography still has a place.

What heat source is best?
A variable-temperature heat gun is ideal. Avoid open flames. Hairdryers aren’t hot enough.

Will it bleed on plywood?
It can, depending on glue lines and porosity. Use a very thin coat and make a test tile first.

Can I use sticky-back vinyl as a stencil?
Yes—press edges firmly, apply minimal gel, and lift slowly.

Is the finish permanent?
The scorch effect bonds to the surface fibres. Seal to protect from abrasion and moisture.

How far does 4oz (120ml) go?
It depends on coverage and technique; with thin coats and stencils, you can complete dozens of small pieces.

Is it safe for children’s toys?
This is an adult craft product. Keep out of reach of children. If decorating items for kids, ensure surfaces are fully cured and sealed, and avoid chew zones.

Will it work on bamboo boards?
Usually yes, but bamboo’s density varies—run a test patch and adjust heat passes.

Simple Troubleshooting

• Edges look fuzzy: Too much gel or a porous, unsanded surface. Sand finer, use less product.
  
• Patchy scorch: Inconsistent heat distance. Keep the heat gun moving evenly.
  
• Stencil lifted gel: Allow a brief dwell time, then peel slowly back on itself.
  
• Design too light: Add another controlled heat pass or apply a second ultra-thin gel layer.
  
• Burn marks outside design: Mask wider margins, lower heat intensity, and reduce dwell.
  

Responsible Crafting in NZ

Support local: pair FLYSEA Scorch Burning Gel with NZ-made blanks and custom stencils from local makers. Follow your city council’s disposal guidance for craft liquids, and ventilate indoor spaces—especially in winter when windows stay shut.

Who It’s For

• Hobbyists and DIYers who want pro results without specialised pyrography skills.
  
• Market stall owners and small brands needing crisp, repeatable logos.
  
• Wedding stylists and event planners crafting signage and table décor.
  
• Teachers/demonstrators (with adult supervision) in workshops or makerspaces.
  

Who Should Skip It

• Users needing deep, carved relief or tactile grooves (choose a pyro pen or CNC).
  
• Those working exclusively on sealed, glossy, or oily surfaces that resist penetration.
  
• Anyone without access to proper ventilation or safe heat-tool handling.
  

Value for Money

A compact bottle that stretches across many projects, thanks to thin-coat application. If you sell crafted goods locally, the time saved on lettering alone can pay for the product in a weekend market run.

Simple Application Checklist (Copy-Friendly)

• Sand → Dust off → Mask edges → Thin coat → Lift stencil → Short dwell → Heat passes → Cool → Dust → Seal (optional)
  

Technical Details & Guidance (Consolidated)

• Bottle size: 4oz / 120ml
  
• Consistency: Brushable gel, suited to sponge/dauber use
  
• Dry time (pre-heat): Short; allow brief set before heat activation
  
• Activation: Heat gun (variable temp preferred)
  
• Coverage: Project-dependent; thin layers recommended
  
• Clean-up: Soap & water while wet; mechanical removal when scorched
  
• Shelf life: Use within a reasonable period after opening; keep sealed
  
• Compatibility: Raw woods first; test composites, papers, veg-tan leather
  

Responsible Use & Legal Notes

Use strictly as directed for decorative crafts. Keep away from open flames and ignition sources. The maker/user is responsible for testing suitability for each material and intended context, especially where local standards or food-safety considerations apply.

Simple Care for Tools & Stencils

• Rinse brushes and sponges straight after use.
  
• Wipe mylar stencils with damp cloth while product is still wet.
  
• Store vinyl masks flat; avoid high heat that can distort adhesive.
  

Project Ideas to Try This Weekend

• Custom bach sign: “Welcome to the Bach” on a pine plank; seal with clear coat.
  
• Cafe price tags: Small birch plywood tags with logo burned via stencil.
  
• Wedding place names: Light card with subtle scorch along letter edges—gentle heat only.
  
• Gift boards: Keep the design away from the chopping area; seal non-contact surfaces.
  

NZ-Centric Shipping, Returns & Support (Generic Copy)

• Shipping: Fast dispatch NZ-wide; North & South Island coverage. Rural delivery available.
  
• Returns: Change-of-mind window per store policy; product must be unopened and resellable.
  
• Support: Basic use guidance included; community tips and maker groups can help you refine technique.
  

(Replace with your store’s exact policies and links.)

Why Choose FLYSEA Scorch Burning Gel

• Practical alternative to pyro pens for stencil work
  
• Repeatable, brand-ready results for small businesses
  
• Friendly learning curve and tidy workflow
  
• Works with popular stencil materials and cutting machines
  
• Compact, efficient, and easy to store
  

At-a-Glance Pros & Cons

Pros: Quick learning, crisp stencils, good for batches, economical use, clean-up while wet.
Cons: Requires a heat gun, not ideal for sealed/oily surfaces, results vary by substrate (testing required).

What to Pair It With (Optional Add-Ons)

• Variable-temp heat gun
  
• Mylar or vinyl stencils (reusable)
  
• Fine-grit sandpaper & tack cloth
  
• Low-tack spray adhesive / painter’s tape
  
• Clear water-based topcoat
  

Plain-English Directions (Short Form)

Shake → Test on scrap → Apply thinly through stencil → Wait briefly → Heat evenly until dark → Cool → Seal if needed.