Color: GRAY - 2in1 Dental Aluminum Oxide Micro blaster Dental Alumina Air Abrasion Polisher Microetcher Sandblasting Sandblaster Lab Dentistry

Origin: Mainland ChinaCommodity Quality Certification: ceMaterial: Metal2in1 Aluminum Oxide Micro Blaster Dental Alumina Air Abrasion Polisher Microetcher Sandblasting Sandblaster Lab Dentistry ToolPRODUCT DESCRIPTIONAluminum oxide microblaster is a handheld dental sandblasting unit for intraoral sandblasting and dental lab applications Surface area and surface reactivityare dramatically increased for maximum bonding. The Aluminum oxide microblaster have stainless steel construction and a replaceable carbide tip that rotates 360 degrees. The Aluminum oxide microblaster unit is fully autoclavable (except removable jar), and the Aluminum oxide microblaster has only anautoclavable nozzle.Packing ListAlumina sandblasting gug *1 Nozzle*2powderjar*2 Sealing ring *6 Bottle cap*1INSTALLATIONThe Aluminum oxide microblaster requires compressed air of 40 to 100 psi (2.6 to 6.6 bars) at 1 cfm (30ccm/m). There is a significant reductionin sandblasting action as the pressure is reduced below 60 psi.Bottled gas such as Co,or highly compressed air can be used with a requlator. Oxygen, flammable, or toxic gases must not be used. Dehydrated air is not required; however, large particles in the air line can plug up the Aluminum oxide microblaster.A water trap filter is recommended. Do not use Teflon tape to seal pipe joints.HOOK UP KITS1. Quick disconnect kits: These kits allow multiple connections in operatory and in the lab with a common connector. They are the preferred connection method due to the greater pressures generally available.2. High speed handpiece line adaptors: Allow easy connection to 4-Hole, 2-Hole, Kavo & Siemans-Sirona Quick Couplers and EMS. Pleasenote that pressures provided may be low, without readjusting.HOOK UP IN OPERATORYUsing the quick disconnect kit:1. Locate the air pressure supply line close to the desired work area.2. Turn off air. Cut the air line and install the tee fitting.3. The female disconnect part of the fitting contains the automatic shut off and may be panel mounted.4. Install the male end of the quick disconnect onto the Microetcher line5. The Aluminum oxide microblaster includes a rear adapter for a direct connection to a high speed handpiece line.* If the air supply line from the compressor to the chairside cart is not 1/4" OD polyethylene tubing, special fittings are required.Danville Materials carries fittings for 1/4", 3/8", 1/2" copper and 3/8" polyethylene tubing.HOOK UP IN LABA laboratory stop cock may be used for the compressed air connection. The valve or cone assembly may be unscrewed so a tee may be installed. Or adapters are available with a female quick disconnect fitting or without a quick disconnect.OPERATIONThe Aluminum oxide microblaster was designed to be held almost like a pencil,allowing the thumb to activate the finger button control. Hold the nozzle 2mm to10mm from the surface Sandblasting is most effective using continuous, overlappino sweeps rather than fast,erratic movements. A surface shoulo appear evenly etched with a dull texture for optimal results.Excessive sandblasting will actually erode some surfaces such as porcelain.Experiment on metal and glass. These will simulate both precious and nonprecious alloys and porcelain.Nozzles are changed by unscrewing the collar completely. It is important to remove abrasive from the threads, collar and mating surfaces prior to reinstallation.SAFETYDo not spray into gingiva for risk of air embolism.Protect eyes, nose & optical equipment.Have patient hold breath during intraoral spray, or use rubber damClinical use which is not in accordance with the indicated uses listed in this manual should be avoided.